Select Category
POSITIONING SYSTEMS
Linear Motor Systems
LinMot motors are electromagnetic direct drives in tubular form. The linear motion is produced purely electrically and wear-free, without any intermediate coupling of mechanical gearboxes, spindles, or belts. The linear motor consists of just two parts: the slider and the stator. The slider is made of neodymium magnets that are mounted in a high-precision stainless steel tube. The stator contains the motor windings, bearings for the slider, position capture sensors, and a microprocessor circuit for monitoring the motor.
MM Series
Based on the above structure, the product has the following characteristics：
* Not only deceleration, but also high rigidity and high axial load；
* Perfect servo linear motion scheme
* A variety of installation methods
* IP65
* Super bearing support
* Ultra-quiet
* High motion characteristics
* Simple application
* High reliability
Planetary Reducer SS Series
Based on the above structure, the product has the following characteristics：
- High Precision Reducer
- XP information introduction
CP Planetary Series
Based on the above structure, the product has the following characteristics：
* Not only deceleration, but also high rigidity and high axial load
* Perfect servo linear motion scheme
* A variety of installation methods
* IP65
* Super bearing support
* Ultra-quiet
* High motion characteristics
* Simple application
* High reliability
CP-C2 Series
- Low noise
- Low vibration
- XTTS teeth shape
- Extremely compact planetary
- Product type : Planetary gear
- Reduction ratio range : 3 ~ 100
- Rated output torque : 3.5Nm ~ 180Nm
- Lost motion : 2 ~ 20 arcmin
- Characteristic : Typical planetary gear
CRP Series
- Clean Rack Pinion
- Clean installation & Operation
- Integer movement
- Multiple tooth contact
- High speed (High productivity)
- High precision
- High efficiency
- Extremely silent
- High dynamics
- Simple to use
- Various selection & wide application fields
- Product type : Rack & Pinion
- Rated torque : 10Nm~1000Nm
- Rated tangential force : 400N~1000N
- Permitted speed : STD.6m/s, Max.10m/s
Cycloidal Drive High Precision Reducer
- Application of speed reducer：tool changer of numerical control equipment, turntable, robot joint, stacker, positioner, welding machine, radar, antenna, navigation equipment, riveting machine, aluminum machine, automatic shooting platform, bullet changing system, 3D printer, five-axis water jet, multi-axis grinding equipment, application of turntable in clean workshop, wind tunnel test, etc.
- High precision：ultra-low backlash, transmission backlash less than 1 arc minute.
- Low noise, low vibration and high efficiency：improve the supporting structure of high-speed components to reduce noise and vibration, and the efficiency is greater than 88%.
- Improved sealing structure：ensures the complete sealing of the input/output end with IP65 protection level.
- Maximum deceleration range：the range of deceleration ratio is 19~5000 (partially customized).
- Easy assembly：The complete input support structure and sealed output structure make assembly easier.
- Low input inertia and high dynamic response：the highest planetary gear structure reduces the input inertia and improves the response characteristics of servo motor.
- Better power transmission：the unique continuous rolling contact and crankshaft cam structure can reduce meshing failure and fatigue damage, and the more linear structure increases the torque rigidity.
- Torque range：19Nm~40000Nm (partially customized)
- Lifetime lubrication-free： the product has been filled with special lubricating grease at the factory, and is life-long maintenance-free.
Lifting Stages (HT Series)
Our lifting stages are used for high precision, vertical positioning. They are used separately or in combination with linear stages, if probes or components need to be adjusted vertically.
Linear Stages (PMT, PLT Series)
All axis modules are available in various travel lenghths and can be integrated easily in the setup of various applications.
Micro Stages (MT Series)
Micro stage for demanding environments. Equipped with precision cross roller bearings and piezo motor
PH Series
- Maximize reduction range
- Superior torsional rigidity
- Improved sealing structure
- Easier assembly
- Product type : Hollow type high precision transmission
- Reduction ratio range : 40 ~ 800
- Rated output torque : 30Nm ~ 7200Nm
- Lost motion : 1 arcmin
Rotary Stages (DT Series)
Our rotary stages have been developed to match our linear, micro and lifting stages. They can be easily combined to form complex multi-axis systems. Especially they are used for applications in metrology or in laser technology.
XY Stages (KDT, KT Series)
Our high precision XY stages are universal in use and their operating parameters correspond with the most important requirements in metrology and test engineering.
Servo Dynamics Sdn Bhd
No. 17, Solok Kekabu 1,
Permatang Damar Laut,
11960 Bayan Lepas,
Penang, Malaysia.
www.servo.com.my
Co. Reg. No. 200701009051 (767053A)